Banner U-Gage Ultrasonic Sensor Manual de usuario Pagina 55
- Pagina / 66
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
SENSORS
More information online at bannerengineering.com346
LIGHT GAUGING ULTRASONIC MEASURING ARRAYS RADAR
A-GAGE
®
High-Resolution MINI-ARRAY
®
Controller Specifications
Power Requirements
16 to 30V dc @ 1.0 A (typical: 0.5 A @ 16V dc)
Inputs
Sensor input: Emitter and receiver wire in parallel to ve terminals.
Trigger (Gate) input: Optically isolated, requires 10 to 30V dc (7.5 kΩ impedance) for gate signal
Remote alignment input: Optically isolated, requires 10 to 30V dc (7.5 kΩ impedance) for alignment sequence signal
Discrete (Switched) Outputs
NPN outputs: Open collector NPN transistor rated at 30V dc max., 150 mA max.
PNP outputs: Open collector PNP transistor rated at 30V dc max., 150 mA max.
All discrete outputs: OFF-state leakage current: less than 10 µA @ 30V dc
ON-state saturation voltage: less than 1V @ 10 mA; less than 1.5V @ 150 mA
Serial Data Outputs
RS-232 or RS-485 interface. (Up to 15 control modules may be given unique addresses on
one RS-485 party line.)
ASCII or binary data format
9600, 19.2K or 39.4K baud rate
8 data bits, stop bit, and even, odd or no parity
Analog Outputs
Voltage-sourcing outputs: 0 to 10V dc (25 mA current limit)
Current-sinking outputs: 4 to 20 mA (16 to 30V dc input)
Resolution: Span / Number of sensing channels
Linearity: 0.1% of full scale Temperature variation: 0.01% of full scale per ° C
Output Configuration
MAHCVP-1: Two PNP discrete (switched), two 0-10V voltage sourcing
MAHCVN-1: Two NPN discrete (switched), two 0-10V voltage sourcing
MAHCIP-1: Two PNP discrete (switched), two 4-20 mA current sinking
MAHCIN-1: Two NPN discrete (switched), two 4-20 mA current sinking
System Programming
Via RS-232 interface to PC-compatible computer running Windows
®
95, 98, NT, ME, XP or 2000 and using software supplied with each
control module.
Status Indicators
Output 1 (Red): Lights to indicate Discrete Output #1 is active
Alarm (Red): Lights to indicate Discrete Output #2 is active
Gate (Red): Lights to indicate Trigger (Gate) is active
Align (Green): Lights to indicate emitter and receiver are aligned
Diagnostics indicator: (Key on controller side label) Identifies System errors and status
Construction
Polycarbonate housing; mounts to flat surface or directly onto 35-mm DIN rail
Environmental Rating
NEMA 1; IP20
Operating Conditions
Temperature: 0° to +50° C Relative humidity: 95% @ 50˚ C (non-condensing)
Certifications
Hookup Diagrams
0-10V sourcing: MI25 (p. 764) 4 to 20 mA voltage: MI26 (p. 764)
A-GAGE
®
High-Resolution MINI-ARRAY
®
Emitter/Receiver Specifications
Emitter/Receiver Range
380 mm to 1.8 m
Minimum Object Sensitivity
2.5 mm
Sensor Scan Time
1.8 to 58.4 milliseconds, depending on scanning method and sensor length plus 1 millisecond post processing time for controller.
Power Requirements
12V dc ±2%, supplied by controller
Connections
Sensors connect to controller using two 5-conductor quick-disconnect cordset (one each for emitter and receiver), ordered separately. Use
only Banner cordset, which incorporate a “twisted pair” for noise immunity. Cordsets measure 8.1 mm in diameter and are shielded and
PVC-jacketed. Conductors are 20 gauge (0.9 mm). Emitter and receiver cordset may not exceed 75 m long, each. See page 347.
Status Indicators
Emitter: Red LED lights to indicate proper emitter operation
Receiver: Green indicates sensors aligned
Yellow indicates marginal alignment of one or more beams
Red indicates sensors misaligned or one or more beam(s) blocked
Construction
Aluminum, with black anodized finish; acrylic lens cover
Environmental Rating
NEMA 4, 13; IP65
Operating Conditions
Temperature: 0° to +50° C Relative humidity: 95% at 50° C (non-condensing)
Certifications
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
- MEASUREMENT & INSPECTION 1
- Light Gauging Sensors 2
- Measuring Light Screens 3
- Ultrasonic Sensors 3
- LIGHT GAUGING SENSORS 4
- LT3 Sensing Ranges 5
- LT3, 12-24V dc 6
- LT3 Specifications 6
- = Visible Red Laser 8
- 90% White to 18% Gray 8
- 90% White to 6% Black 8
- REFLECTORS 8
- Laser Gauging Sensors 9
- LT7, 18-30V dc 10
- LT7 Specifications 10
- (cont’d) 11
- Brackets 11
- Cordsets 11
- Actuators,Indicators 12
- & Illuminators 12
- Serial Adapters 13
- LH Specifications 13
- Short-range Laser Sensors 14
- LG5 and LG10 Specifications 15
- LG10, 12-30V dc 15
- ULTRASONIC SENSORS 17
- Long-Range Ultrasonic Sensor 18
- QT50U, 10-30V dc 19
- QT50U DC Specifications 19
- Effective Beam Patterns 22
- Compact Barrel-Mount 23
- Ultrasonic Sensor 23
- S18U Specifications 24
- S18U (Typical) 25
- S18U (with 500 mm Plate) 25
- Maximum Target Rotation Angle 25
- Ultrasonic WORLD-BEAM 26
- WORLD-BEAM 27
- QS18U Specifications 27
- Ultrasonic Wave Guides 28
- T30UX/T30U 29
- T30UX, 10-30V dc 30
- T30U, 12-24V dc 30
- ACCESSORIES 31
- T30UX Specifications 32
- T30U Specifications 33
- Stainless Steel Opposed-Mode 37
- M25U Specifications 38
- Opposed Dual Range Sensors 39
- T18U Specifications 40
- Flexible Ultrasonic Sensors 41
- Q45U Specifications 43
- bannerengineering.com 339 48
- Mini QD (With Shield) 48
- Euro QD (With Shield) 48
- MEASURING ARRAYS 49
- EZ-ARRAY 50
- bannerengineering.com 343 52
- Communication Cordsets 52
- See page 739 Model 52
- High-Resolution MINI-ARRAY 53
- bannerengineering.com346 55
- MINI-ARRAY 57
- bannerengineering.com 351 60
- Controller Specifications 61
- bannerengineering.com 353 62
- DB9 Communication 62
- Retroreective Sensors 63
- QT50R Specifications 64
- Web Only 66
Relacionado con productos y manuales para De medición, control y control Banner U-Gage Ultrasonic Sensor
(16 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales