Banner U-Gage Ultrasonic Sensor Manual de usuario descargar pdf (Pagina 16)

LIGHT GAUGING

LT3

LT7

ULTRASONIC

MEASURING

ARRAYS

RADAR

More information online at bannerengineering.com 307

Photoelectrics

Sensors

Fiber Optic

Sensors

Special Purpose

Sensors

Measurement &

Inspection Sensors

Vision

Wireless

Lighting &

Indicators

Safety

Light Screens

Safety

Laser Scanners

Fiber Optic

Safety Systems

Safety Controllers &

Modules

Safety Two-Hand

Control Modules

Safety Interlock

Switches

Emergency Stop &

Stop Control

L-GAGE

LG5 and LG10 Speciﬁcations

Adjustments

Response speed: Push button toggles between Slow, Medium, and Fast (see Output Response Time)

Window limits (analog or discrete): TEACH-mode programming of near and far window limits. Limits may also be taught remotely

using TEACH wire.

Analog output slope: The first limit taught is assigned to the minimum analog output (0V dc or 4 mA).

Laser Control

To enable laser: Connect green wire to +5 to 30V dc

To disable laser: Connect green wire to 0 to +2V dc (or open connection) 250 millisecond delay upon enable/disable

Indicators

Green Power ON LED: Indicates when power is ON, overloaded output and laser status.

Yellow Output LED: Indicates when discrete load output is conducting.

Red Signal LED: Indicates when target is within sensing range and the condition of the received light signal.

Tri-color Red/Green/Yellow TEACH LED: Indicates sensor is ready for programming each limit (indicates Red for analog output,

Green for discrete, and Yellow for simultaneous analog and discrete.)

Yellow Fast/Slow LEDs: Combination of 2 lights ON or OFF indicates 1 of 3 response speeds

Construction

Housing: Zinc alloy die-cast, plated and painted finish

Cover plate: aluminum with painted finish

Lens: acrylic

Environmental Rating

IP67; NEMA 6

Connections

2 m or 9 m 7-conductor shielded PVC-jacketed attached cable, or 150 mm 8-pin Euro-style pigtail quick-disconnect.

Mating QD cordsets are purchased separately. See page 307.

Operating Conditions

Temperature: -10° to +50° C Relative humidity: 90% at 50° C (non-condensing)

Vibration and

Mechanical Shock

Vibration: 60 Hz, 30 minutes, 3 axes

Shock: 30G for 11 milliseconds, half sine wave, 3 axes

Application Notes

For comparison, a white ceramic test surface has approximately 91% of the reflectivity of a white Kodak test card with a matte finish.

A dark gray ceramic test surface has approximately 11% of the reflectivity of a white Kodak test card with a matte finish.

(Allow 15-minute warm-up for maximum linearity.)

Certiﬁcations

Hookup Diagrams

NPN Models: MI06 (p. 759) PNP Models: MI07 (p. 759)

(cont’d)

Brackets

LG5/LG10

SMBLG SMBLGA

pg. 656 pg. 656

Euro QD (With Shield)

See page 689

Length

8-Pin

Threaded Straight

2 m MQDC-806

5 m MQDC-818

9 m MQDC-830

Cordsets

Additional cordset information available.

See page 679.

Additional brackets and information available.

See page 620.

Repeatability/Resolution Curves

☼

= Visible Red Laser

LG5

Resolution/Repeatability (microns)

Distance (mm)

45 50 55 60 65

Medium

Fast

Slow

Range: 60 mm Mode: Diffuse LED:

☼

LG10

Resolution/Repeatability (microns)

Distance (mm)

75 95 105 1 1 5 125 135

100

125

150

175

200

225

Medium

Fast

Slow

Range: 125 mm Mode: Diffuse LED:

☼

RRC-2

RRC-1

Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 65 66

Comentarios a estos manuales

Sin comentarios

Banner U-Gage Ultrasonic Sensor Manual de usuario Pagina 16

Comentarios a estos manuales

Relacionado con productos y manuales para De medición, control y control Banner U-Gage Ultrasonic Sensor