Banner SC22-3E Safety Controller with Ethernet Manual de usuario Pagina 84
- Pagina / 130
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Fault
Code
Displayed
Message
Additional
Message
Further Steps and Checks
• The AVM may be disconnected; check the wiring.
• Perform a System Reset to clear the fault and cause another test to occur.
2.1
Concurrency
Fault
Cycle Input
On a dual-channel input with both inputs in the Run state, one input went to the Stop
state then back to Run.
• Check wiring.
• Check input signals.
• Consider adjusting debounce times.
2.2
Simultaneity
Fault
Cycle Input
On a dual-channel input, one input went into the Run state but the other input did not
follow within 3 seconds.
• Check wiring.
• Check input signal timing.
2.3 or 2.5
Concurrency
Fault
Cycle Input
On a complementary pair with both inputs in the Run state, one of the inputs changed
to Stop then back to Run.
• Check wiring.
• Check input signals.
• Check power supply providing input signals.
• Consider adjusting debounce times.
2.4 or 2.6
Simultaneity
Fault
Cycle Input
On a complementary pair, one input went into the Run state but the other input did not
follow within the time limit.
• Check wiring.
• Check input signal timing.
2.7 Internal Fault
Check Terminal
xx
Internal failure – Contact Banner Factory (see section 9.2 Repairs and Warranty Serv-
ice on page 82).
2.8 – 2.9 Input Fault
Check Terminal
xx
Input stuck high.
• Check for shorts to other inputs or other voltage source.
• Check input device compatibility.
2.10 Input Fault
Check Terminal
xx
• Check for short between inputs.
2.11 -
2.12
Input Fault
Check Terminal
xx
• Check for short to ground.
2.13 Input Fault
Check Terminal
xx
Input stuck low.
• Check for short to ground.
2.14 Input Fault
Check Terminal
xx
Missing test pulses.
• Check for short to other inputs or other voltage source.
2.15 Open Lead
Check Terminal
xx
• Check for open lead.
2.16 –
2.18
Input Fault
Check Terminal
xx
Missing test pulses.
• Check for short to other inputs or other voltage source.
SC22-3/-3E Safety Controller Instruction Manual
84 www.bannerengineering.com - tel: 763-544-3164 P/N 133487 rev. C
- Original Instructions 1
- Contents 2
- Contents 3
- 4 P/N 133487 rev. C 4
- Contents 5
- 1 About This Document 6
- 1.3 Standards and Regulations 7
- 1.4 Contact Us 8
- 2 Overview 9
- 2.1 Ethernet-Compatible Model 9
- 2.2 Applications 10
- 2.3 Design and Testing 10
- 2.4 Components 10
- 2.4.2 USB Connections 11
- 2.4.3 Ethernet Connections 11
- 2.4.4 SC-XMP Programming Tool 11
- 2.5.1 Onboard Interface (OBI) 12
- Accessing Fault Codes 14
- PCI Software Compatibility 15
- 2.6.2 Safety Outputs 16
- 2.6.3 Status Outputs 17
- 2.6.4 Virtual Status Outputs 17
- 2.7 System Settings 18
- 2.8 Internal Logic 19
- 2.9 Password Overview 20
- 3.3 Ethernet Cordsets 22
- 3.4 Interface Modules 22
- 3.5 Specifications 23
- 3.5.1 Dimensions 25
- 4 System Installation 26
- 4.1 Appropriate Application 26
- 4.3 Safety Input Devices 27
- SO1 SO2 SO3 28
- S = Simultaneous 29
- C = Concurrent 29
- Signal Change-of-State Types 30
- Signal Debounce Times 30
- 4.4 Non-Safety Input Devices 31
- 4.5 Input Device Resets 33
- 4.6 Safety Input Function 35
- 4.6.2 Two-Hand Control (THC) 36
- 4.6.3 Enabling Devices 36
- 4.6.4 Mute Function 37
- 4.6.5 Bypass Function 38
- 4.7.2 Safety Outputs 41
- Safety Input 42
- (ON-Delay) 42
- (OFF-Delay) 42
- (To SO 1A) 46
- (To SO 1B) 46
- 1A 1B 2A 2B 3A 3B A2 47
- 4.8 Status Outputs 50
- 4.9 Virtual Status Outputs 52
- 4.10 Commissioning Checkout 52
- 5.1.1 Configuration Tools 53
- 5.1.2 Build a Configuration 54
- Create a New Configuration 55
- Add an Input Device 55
- Finish the Configuration 57
- System Reset 59
- 5.1.4 Other Functions 60
- Export Documents 61
- Print Options 61
- Run Mode 63
- Configuration 63
- 6.2 Run Mode 64
- 6.3 Configuration Mode 64
- 6.3.3 Confirm Configuration 65
- 6.4 Edit Configuration 66
- 6.4.3 Outputs/System Settings 67
- 6.5 Add an Input 68
- 7.3.1 Run Mode Screen—OBI 72
- 7.4 Manual Reset 73
- 7.6 Reset Signal Requirements 74
- 8 System Checkout 75
- W1 W2 W3 W4 80
- 9.1 Cleaning 82
- 9 Troubleshooting 82
- 9.4 Recovering from a Lockout 86
- 9.5.1 Fault Log—PCI 87
- 9.5.2 Fault Log Recording—PCI 87
- 9.6.1 View Current Faults—OBI 88
- Device Name 89
- Fault Description 89
- Time Since Fault 89
- Fault Code 89
- Principles 90
- OFFON OFFON 91
- 10.2 Protective (Safety) Stop 92
- OpenOpen 95
- Open Open Open 96
- 24V 24V 24V 97
- 10.4 Optical Sensor 98
- 10.5 Two-Hand Control 100
- 10.6 Safety Mats 103
- Emergency Stop Hookup Options 108
- Category 2 E-Stop Circuit 108
- Category 3 E-Stop Circuit 108
- Category 4 E-Stop Circuit 108
- 10.8 Rope/Cable Pull 109
- S1 S2 S1 S2 111
- 10.9 Enabling Device 112
- ONOFF ONOFF 114
- Lockout/Tagout 115
- 10.11 Mute Sensor Pair 116
- Mute Device Requirements 117
- Inductive Proximity Sensors: 118
- 10.11.4 Mute Enable (ME) 119
- 10.11.5 Mute Lamp Output (ML) 119
- 10.11.7 Mute on Power-Up 120
- < 3s< 3s 122
- < 3s< 3s < 3s< 3s 123
- 11 Ethernet Reference 124
- 11.1 Ethernet Setting Access 124
- 11.3 Support Files 125
- Reserved 127
- 12 Glossary 128
Relacionado con productos y manuales para Maquinaria especial Banner SC22-3E Safety Controller with Ethernet
(4 paginas)
(70 paginas)
(2 paginas)
(4 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales