Banner SC22-3E Safety Controller with Ethernet Manual de usuario Pagina 55
- Pagina / 130
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Create a New Configuration
Open the software program, and a new un-named file is created. You may name the Configuration and the Author, and establish the
system settings at this time.
Double-click the System Settings icon , on the right-hand side of the Tool Bar.
When the pop-up menu appears, name the configuration file, using up to 16 alphanumeric characters.
Add your name in the Author’s name box (up to 10 characters; abbreviate as needed).
Keep or change the default system settings:
• Power up mode: Auto, Manual, or Normal (default), see section 2.7 System Settings on page 18
• Mute on power up: ON or OFF (default), see section 2.7 System Settings on page 18
• Monitored system reset: OFF or ON (default), see section 4.4 Non-Safety Input Devices on page 31
When complete, click OK.
Add an Input Device
Refer to section 10 Input Device and Safety Category Reference on page 90 for more information about each of the input device types.
Click the Add Safety Input icon and the Safety Input Device selection menu appears. It displays the device types the Controller can
accommodate.
Safety Input Devices
Figure 36. Safety Input Device Selection menu
• Emergency stop button
• Rope pull
• Gate (interlock) switch
• Optical sensor (single-/multiple-beam sensors, safety light curtain,
area scanner, etc.)
• Two-hand control device
• Safety mat
• Protective stop (miscellaneous devices)
• Enabling device
• Muting sensors
• Bypass switches
• External device monitoring (EDM or AVM) contacts
Click the Non-Safety Input icon and the Non-Safety Input Device selection menu appears.
Non-Safety Input Devices
Figure 37. Non-Safety Input Device Selection menu
• Manual reset switch
• ON/OFF switch
• Mute enable switch
• Cancel OFF-delay switch
While their functions differ, the procedure to add and configure the two
types of devices is virtually identical. Click on the appropriate icon to se-
lect the desired device and click OK (or double-click on the icon).
SC22-3/-3E Safety Controller Instruction Manual
P/N 133487 rev. C www.bannerengineering.com - tel: 763-544-3164 55
- Original Instructions 1
- Contents 2
- Contents 3
- 4 P/N 133487 rev. C 4
- Contents 5
- 1 About This Document 6
- 1.3 Standards and Regulations 7
- 1.4 Contact Us 8
- 2 Overview 9
- 2.1 Ethernet-Compatible Model 9
- 2.2 Applications 10
- 2.3 Design and Testing 10
- 2.4 Components 10
- 2.4.2 USB Connections 11
- 2.4.3 Ethernet Connections 11
- 2.4.4 SC-XMP Programming Tool 11
- 2.5.1 Onboard Interface (OBI) 12
- Accessing Fault Codes 14
- PCI Software Compatibility 15
- 2.6.2 Safety Outputs 16
- 2.6.3 Status Outputs 17
- 2.6.4 Virtual Status Outputs 17
- 2.7 System Settings 18
- 2.8 Internal Logic 19
- 2.9 Password Overview 20
- 3.3 Ethernet Cordsets 22
- 3.4 Interface Modules 22
- 3.5 Specifications 23
- 3.5.1 Dimensions 25
- 4 System Installation 26
- 4.1 Appropriate Application 26
- 4.3 Safety Input Devices 27
- SO1 SO2 SO3 28
- S = Simultaneous 29
- C = Concurrent 29
- Signal Change-of-State Types 30
- Signal Debounce Times 30
- 4.4 Non-Safety Input Devices 31
- 4.5 Input Device Resets 33
- 4.6 Safety Input Function 35
- 4.6.2 Two-Hand Control (THC) 36
- 4.6.3 Enabling Devices 36
- 4.6.4 Mute Function 37
- 4.6.5 Bypass Function 38
- 4.7.2 Safety Outputs 41
- Safety Input 42
- (ON-Delay) 42
- (OFF-Delay) 42
- (To SO 1A) 46
- (To SO 1B) 46
- 1A 1B 2A 2B 3A 3B A2 47
- 4.8 Status Outputs 50
- 4.9 Virtual Status Outputs 52
- 4.10 Commissioning Checkout 52
- 5.1.1 Configuration Tools 53
- 5.1.2 Build a Configuration 54
- Create a New Configuration 55
- Add an Input Device 55
- Finish the Configuration 57
- System Reset 59
- 5.1.4 Other Functions 60
- Export Documents 61
- Print Options 61
- Run Mode 63
- Configuration 63
- 6.2 Run Mode 64
- 6.3 Configuration Mode 64
- 6.3.3 Confirm Configuration 65
- 6.4 Edit Configuration 66
- 6.4.3 Outputs/System Settings 67
- 6.5 Add an Input 68
- 7.3.1 Run Mode Screen—OBI 72
- 7.4 Manual Reset 73
- 7.6 Reset Signal Requirements 74
- 8 System Checkout 75
- W1 W2 W3 W4 80
- 9.1 Cleaning 82
- 9 Troubleshooting 82
- 9.4 Recovering from a Lockout 86
- 9.5.1 Fault Log—PCI 87
- 9.5.2 Fault Log Recording—PCI 87
- 9.6.1 View Current Faults—OBI 88
- Device Name 89
- Fault Description 89
- Time Since Fault 89
- Fault Code 89
- Principles 90
- OFFON OFFON 91
- 10.2 Protective (Safety) Stop 92
- OpenOpen 95
- Open Open Open 96
- 24V 24V 24V 97
- 10.4 Optical Sensor 98
- 10.5 Two-Hand Control 100
- 10.6 Safety Mats 103
- Emergency Stop Hookup Options 108
- Category 2 E-Stop Circuit 108
- Category 3 E-Stop Circuit 108
- Category 4 E-Stop Circuit 108
- 10.8 Rope/Cable Pull 109
- S1 S2 S1 S2 111
- 10.9 Enabling Device 112
- ONOFF ONOFF 114
- Lockout/Tagout 115
- 10.11 Mute Sensor Pair 116
- Mute Device Requirements 117
- Inductive Proximity Sensors: 118
- 10.11.4 Mute Enable (ME) 119
- 10.11.5 Mute Lamp Output (ML) 119
- 10.11.7 Mute on Power-Up 120
- < 3s< 3s 122
- < 3s< 3s < 3s< 3s 123
- 11 Ethernet Reference 124
- 11.1 Ethernet Setting Access 124
- 11.3 Support Files 125
- Reserved 127
- 12 Glossary 128
Relacionado con productos y manuales para Maquinaria especial Banner SC22-3E Safety Controller with Ethernet
(4 paginas)
(70 paginas)
(2 paginas)
(4 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales