Banner R58 Registration Mark Sensors Manual de usuario descargar pdf (Pagina 9)

P/N 122928 rev. C 9

Banner Engineering Corp.•Minneapolis,MNU.S.A

www.bannerengineering.com•Tel:763.544.3164

R58 Expert

™

Registration Mark Sensors

Supply Voltage and Current

10 to 30V dc (10% max. ripple);

Supply current(exclusiveofloadcurrent):75mA@10Vdc

35mA@30Vdc

Supply Protection Circuitry

Protected against reverse polarity and transient voltages

Output Conﬁguration

Outputsarebipolar:onecurrentsourcing(PNP)andonecurrentsinking(NPN)open-collectortransistor

Output Rating

100 mA max. (each output)

OFF-state leakage current: NPN < 200 microamps; PNP < 10 microamps (see Application Note 1)

NPN saturation:<1.6V@100mA

PNP saturation:<3V@100mA

Output Protection Circuitry

Protected against false pulse on power-up and continuous overload or short-circuit of outputs.

Output Response Time

50microseconds NOTE:1seconddelayonpower-up;outputsdonotconductduringthistime.

Repeatability

15 microseconds

Tri-Color LED

Sensing Image

Rectangular:1.2mmx3.8mm(0.05"x0.15")at10mm(0.39")fromfaceoflens;imageorientedeitherparallelor

perpendicular to sensor length, depending on model (see page 1).

Red: 636 nm Green: 525 nm Blue:472nm

Adjustments

Using push buttons (“+” Dynamic and “-” Static):

Manually adjust discrete output switchpoint using “+” or “-” buttons

Dynamic TEACH (teach on-the-ﬂy) sensitivity adjustment

Static TEACH sensitivity adjustment

Light operate/Dark operate

OFF-delay/ON-delay

Sensing beam color enable/disable

Using Remote TEACH input (gray wire):

Dynamic TEACH (teach on-the-ﬂy) sensitivity adjustment

Static TEACH sensitivity adjustment

Light operate/Dark operate

OFF-delay/ON-delay

Sensing beam color enable/disable

Disable push buttons for security

Indicators

8-segment Bargraph display: Red signal strength indicator relative to taught signal level; higher segment number for

higher sensing contrast

Light Operate: Green OFF-Delay: Green

Dark Operate: Green ON-Delay: Green

Outputs Conducting: Yellow Power/Run Mode: Green

Construction

Zinc alloy die-cast and steel housing with black painted ﬁnish and o-ring sealed lens and lens port cap.

Lens: Acrylic Lens port cap and lens holder: ABS

Push buttons: Thermoplastic elastomer Labels: Polycarbonate

Environmental Rating

IEC IP67; NEMA 6

Connections

PVC-jacketed 5-conductor 2 m (6.5') or 9 m (30') attached cable with internal strain relief, integral 5-pin Euro-style

QD ﬁtting, or 150 mm (6") pigtail with 5-pin Euro-style QD ﬁtting. Mating QD cordsets are purchased separately. See

Quick-Disconnect cordsets on page 10.

Operating Conditions

Temperature:−10°to+55°C(+14°to131°F)

Storage Temperature: −20°to+80°C(−4°to+185°F)

Maximum Relative Humidity: 90% at 50° C (non-condensing)

Vibration and

Mechanical Shock

All models meet IEC 68-2-6 and IEC 68-2-27 testing criteria.

Application Notes

1. NPN OFF-state leakage current is < 200 μA for load impedances > 3kΩ or optically isolated loads.

For load current of 100 mA, leakage is < 1% of load current.

2. Do not mount the sensor directly perpendicular to shiny surfaces; position it at approximately a 15° angle in relation

to the sensing target (see page 8).

3. Minimize web or product “ﬂutter” whenever possible to maximize sensing reliability.

Speciﬁcations

1 2 3 4 5 6 7 8 9 10 11 12

Comentarios a estos manuales

Sin comentarios

Banner R58 Registration Mark Sensors Manual de usuario Pagina 9

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Banner R58 Registration Mark Sensors